Plumbing Basics: Your Starting Point for When Installing a Bathtub
Plumbing Basics: Your Starting Point for When Installing a Bathtub
Blog Article
What are your concepts on How to Install a Bathtub: Install an Acrylic Tub and Tub Surround?
Mounting a bath tub isn't exactly brain surgery, however it does require strong plumbing, carpentry, and also often, tiling skills. Changing an old bathtub with a new one is additionally a moderately hard job. If the old bathtub is readily obtainable, the project can relocate quickly; if you need to open up a wall to eliminate the old bathtub and position the brand-new bath tub, the task is much harder. In either instance, the task is within a house handyman's skills, although you will certainly need a helper to vacate the old tub and embeded in the new one. See to it you have actually qualified on your own for the job as well as are comfortable trying it. Rather than working with a specialist to take over a halfway-completed job, it is far better to consider employing one prior to you begin. Possibilities are you may need an expert plumber to make tube connections.
This short article will assist you mount a new tub in your bathroom if you have currently gotten a new bathtub as well as do not need to transform the plan of your previous water supply pipelines.
Your tools as well as product checklist need to comprise the following:
Removing Old Taps
If you need to replace old taps with brand-new ones as a part of your installment, then the first thing you should do is detach the water system. After doing so, activate the faucets to drain pipes any kind of water continuing to be in the system. The procedure of removing the existing taps can be quite troublesome due to the limited gain access to that is typically the case.
Make use of a basin wrench (crowsfoot spanner) or a faucet tool to undo the nut that links the supply pipelines to the faucets. Have a towel all set for the remaining water that will certainly originate from the pipelines. As soon as the supply pipes have been removed, utilize the exact same tool to loosen up the nut that holds the taps onto the bath/basin. You will certainly require to quit the single faucets from turning during this procedure. Once the faucets have actually been eliminated, the holes in the bath/basin will certainly need to be cleaned of any kind of old sealing substance.
Before going on to fit the brand-new taps, contrast the pipeline connections on the old taps to the brand-new faucets. If the old faucets are longer than the new taps, then a shank adapter is needed for the brand-new taps to fit.
Suitable New Touches
If the tails of the new faucets are plastic, then you will certainly need a plastic adapter to avoid damage to the thread. One end of the connector fits on the plastic tail of the faucet and also the various other end supplies a link to the existing supply pipes.
If you require to fit a monobloc, after that you will require reducing couplers, which attaches the 10mm pipeline of the monobloc to the standard 15mm supply pipeline.
Next, place the tap in the placing opening in the bath/basin guaranteeing that the washers remain in area in between the faucet as well as the sink. Secure the faucet in position with the manufacturer given backnut. When the tap is firmly in place, the supply pipelines can be linked to the tails of the faucets. The taps can either be attached by using corrugated copper piping or with regular tap ports. The previous type needs to be connected to the faucet finishes first, tightening just by hand. The supply pipes can later be linked to the various other end. Tighten both ends with a spanner after both ends have been linked.
Mounting the Bathtub
Utilizing the two wood boards under its feet, position the bath tub in the required position. The wooden boards are practical in equally spreading out the weight of the bath tub over the location of the boards as opposed to concentrating all the weight onto 4 tiny factors.
The next goal is to guarantee that the bathtub is leveled all round. This can be achieved by checking the level and also changing the feet on the tub until the level checks out level.
To mount faucets, fit the bottom of the outermost versatile tap adapter to the proper supply pipeline by making a compression join; then do the very same for the various other faucet.
Turn on the supply of water as well as check all joints as well as new pipework for leaks and also tighten them if needed. Fill the tub as well as also examine the overflow outlet as well as the regular outlet for leaks.
Ultimately, fix the bath paneling as explained in the supplier's instruction manual. Tiling as well as securing around the bath tub should wait until the tub has actually been made use of at the very least when as this will certainly settle it into its last placement.
Preparing for the Installation
Firstly, the supporting framework supplied with the bath ought to be fitted (if needed) according to the maker's directions. Next, fit the taps or mixer to the bathtub. When fitting the tap block, it is important to make sure that if the faucet features a plastic washing machine, it is fitted between the bath and also the faucets. On a plastic bath, it is also sensible to fit a supporting plate under the taps unit to avoid pressure on the bathtub.
Fit the adaptable tap adapters to the bottom of both taps making use of 2 nuts as well as olives (often provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and after that pass the outlet via the hole in the bath. Make use of the nut provided by the maker to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the flexible overflow pipe to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which must be fitted inside the bathroom. Make sure you use every one of the provided washing machines.
Connect the trap to the bottom of the waste outlet on the tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the catch to the electrical outlet. Connect the bottom of the overflow tube in a similar manner.The bath should now be ready to be fitted in its final position.
Tiling Around the Bathtub
In the location where the bathroom fulfills the floor tile, it is needed to secure the joins with a silicone rubber caulking. This is very important as the fitting can move sufficient to fracture an inflexible seal, triggering the water to penetrate the wall surface in between the bath and the tiling, leading to difficulties with moisture and feasible leaks to the ceiling below.
You can pick from a range of coloured sealers to assimilate your components and also fittings. They are offered in tubes and also cartridges, and can securing gaps approximately a size of 3mm (1/8 inch). If you have a larger void to load, you can load it with spins of drenched paper or soft rope. Remember to always fill the bathtub with water prior to securing, to permit the activity experienced when the bathtub remains in use. The sealant can split relatively early if you do not take into consideration this motion before sealing.
Conversely, ceramic coving or quadrant floor tiles can be utilized to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and also cut to dimension, are likewise easily readily available on the marketplace. It is recommended to fit the tiles utilizing water-resistant or water-proof adhesive and also grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
We are very taken with How to Install a Bathtub Yourself and I hope you enjoyed the new page. You should take the time to share this write-up if you enjoyed it. Thanks a lot for your time invested reading it.
Preventative solutions offered. Report this page